Over the years in a workshop, you will add more tools to your tool, collection and they all have one problem in common, because I can see more power, cost and tools here, and I want to change that. The easiest way probably would be to upgrade everything to fit tool because they have their nice plugin system, but I really can't afford that by far so, I try to make a kind of plugin quick connection system myself. The only problem there is that the market for these quick connectors is pretty small and I really only could find one, that's it, and once I bought our the nitrate power con through one connectors and that's what it works very simple, a little longer they are connected. But this has these were the only ones that I could find and, of course, my body enough to put one on all the machines that I had on the table now to install these. I, of course, have to open up all the tools and remove the old power cords and I'm doing that that way, because if it turns out to not work, I can't put them to original state. So I also won't throw away the original power cords. Now a new little piece of cord and I'm putting some curls over the ends. Now I can already put them in place. Power tools usually have some kind of rubber sleep at the end. That extent a little bit, but I want to mount the connectors right behind here, so there's no space for the rubber sleeve, but if I mount it just like so then it's a little opening at the end. So, to take up that space a little bit, I made this little wooden sleeve at least the front part of the relatively for the wood, and this fits here and now it doesn't fit at all. That'S not good! Now, after changing the shape, a little bit outfits. Okay, now I'm selling a plug on this end, I had to unscrew it again and put these parts on the cords first, but now it's pretty much already done this one goes and thinks so and that's it. I quickly write up the mating plugs to the old power pod of the Dremel and work [, Music, ] and probably come back and make this a little bit longer. So I can bend it all the way, but principle on installing these is super simple. I think this are a little bit more easy amount of flexibility. I want to fold all the tools yeah, so I'm just doing that ten times again that will probably take away, and that looks inside the stick, though good joke mechanism for the action. I also changed. My strategy on picking out the right cable link, so I first mounted it to the long one and now, with the tool open, I can see that it needs to be about this long, so circular saw was very easy, but now that hammer drill quite complicated the Wires go here under the switch and then from this side into a switch well that took a bit longer, but not as difficult as expected. Let'S roll again was pretty simple because I only had to take off this little cover here at the handle and I also left a rubber sleeve in place because it's pretty big has a complex shape, but it's also pretty short. So it's okay as it is, but now this sure is again complicated because everything is was covered under here. Wires also have different links, and this one needs to connect them. Sometimes it's amazing how minimalistic these tools are. This will never, for example, motor sanding pad. That'S it now the Devon tender. It just looks like it belongs there. It fits their color scheme just perfectly on this sander the rubber sleeve in the back is ridiculously long. Why would you need that? The good thing on this sander is that it's not enough to just take off this cap. https://felixfurniture.com/best-benchtop-jointer/ have to open up the whole thing, and why is this good? Well now we can see more of the inside of such a sander, but that was less exciting than I thought it would be well. Most of the mechanism is inside, there's caffeine, so yeah, it's just a motor one coffee feature of the center's, also that it dampens the vibration and that really works. It'S amazing and it's realized with just foam pads on all sides, but it also only works on the high settings, some of the high RPM's dial one in five or six. That'S why I use it for woods in the lowest setting so for before one the low rpms, there's vibrates quite hard, but so would you only use it in the higher rpms and there yeah? Yes, pretty much, no vibration, it's super comfortable to use and all that's needed is the right kind of foam pad. That'S pretty cool, oh dear, the straw will be another challenge. Well, I think the throat won't be part of my system because it just can't open the switch. I can open it halfway, but then the trigger blocks me from opening it all the way and I get nowhere. I can get off the trigger so and I leave it like it is for now. If any of you has already opened this exact drill and can tell me where the trick is, please let me know, but it still works. The angle grinder was relatively simple again and you think you switch it on in the front. No, you switch it on in the back now that all this was equipped with this port, except for the stroke and now you can also see the beauty of all these tools, and here are the most power cords. Now it's time to make the new power cords with the mating plug there for about 20 minutes of good quality and rubber sleeve cable. It'S also important that I used to write flux for the power cord, because the ones I put on the tools have the contacts open and I can touch them. I shouldn't do that with the power cord that's plugged into the wall, this one they are. The contacts protected there's no way to touch those now installing the plug is basically the same as with the other ones, with the only change it here also wire up the earth wire. You know none of my current tools: users, it amania, add a tool in the future and it is - and it's also no additional effort. The other end gets a regular wall plug. So now I made five power. Cords 303 me alone to our fight me long. So I hope I never have to curse about a nominal cable anymore. Also, one of both links I make with an angled wall clutch, and I also got three of the two plugs left over. So who knows? Maybe computer yeah, you know it's to have the tools that I use most frequently on the wall. That would have been impossible with all the cords still attached and to have the power coats always plugged into the wall. We get the moment and when we need to use, for example, the center and just grab it from the wall rebel court when it is - and I can start working when I'm done just gon na wait put the tool away, is truly simpler than that so yeah. Okay of that now I do say that this was not a cheap upgrade, because all the connectors I bought cost about 100 years and the cable plus will connect us for about 30 euros. But I think it's worth the convenience and of course I bought it enough to hook up all